SC M37

Build and Restoration Threads Belong Here

Moderators: Cal_Gary, T. Highway, Monkey Man, robi

Post Reply
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

SC M37

Post by sturmtyger380 »

Okay my 2015 commitment was to start on the M37 project. I have been cleaning out a bay of the shop and had this rim that was lying around.

So I mounted one of my tires on it. Well its a start. :roll:


Tube and flap in.

Image

Tire placed on the rim.

Image

Stomped the lock ring down and confirmed it is in the grove.

Image

Chained up ready to inflate.

Image

All inflated and now at 40 psi.

Image

Primed the lock ring and wheel.

Image
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
User avatar
m-37Bruce
1SG
1SG
Posts: 2340
Joined: Fri Oct 19, 2007 8:21 pm
Location: Midlothian,VA

Re: SC M37

Post by m-37Bruce »

Looking good, amazing what happens with no planning!
Bruce,

1953 M-37 w/ow

Retired Again

Keep Em Rollin'

VMVA
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

I got the spare transmission I have out and need to replace the input shaft as it has gotten rusty.

So since I will swap this one into the truck someday I can say I started? :)

Tool I made to pull the bearing and input shaft.

Image

The tool worked well.
Image

Looks like time for a sleeve.

Image

Alan
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
Elwood
MSGT
MSGT
Posts: 937
Joined: Mon Oct 24, 2011 9:34 am
Location: Water Winter Wonderland

Re: SC M37

Post by Elwood »

Creative work on the main bearing removal tool. 8)

I've been waiting on my machinist to make one as shown in the TM 9-8031-2 manual. If I can dig up a damaged bearing retaining nut (the left hand threads and the lack of brass drifts by previous owners seems to result in more than a few with munged up flats), maybe I'll weld it to a square plate with a hole in the center, tap a couple of holes on the sides, and have my own tool.
Last edited by Elwood on Wed Feb 04, 2015 5:13 pm, edited 1 time in total.
“When a long train of abuses and usurpations, pursuing invariably the same Object evinces a design to reduce them under absolute Despotism, IT IS THEIR RIGHT, IT IS THEIR DUTY, TO THROW OFF SUCH GOVERNMENT...” -Declaration of Independence, 1776
T. Highway
Moderator
Moderator
Posts: 1791
Joined: Thu Jul 09, 2009 4:57 am
Location: S.E. Wisconsin, USA, Earth

Re: SC M37

Post by T. Highway »

Alan,

That's the way to adapt and overcome the bearing removal. Nice job!

Bert
1952 M37 W/W Rebuild @ 59% complete
Engine rebuild @ 95% complete
1985 M1009, 1990 M101A2, 2008 M116A3 Pioneer tool trailer
MVPA # 24265
NRA Life Member
NRA Cert. Personal Protection Pistol Instructor
NRA Cert. RSO
Class III RSO/KCR
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

You don't have to tap holes in the plate just weld some nuts over holes in the plate.

I should have made it wider as I had to remove the snap ring on the bearing to allow it to push on the housing. Was just a millimeter off on each side, dang it.

Alan
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

I decided to make my own reverse idler shaft puller.

Here is what I started with. You can see the original bolt and metal plate that holds the shaft in.

Image

First step is the file the grade 8 washer to match the M37 metal piece and check to see that it fits in the slot on the shaft.

Then weld it to the one inch iron gas pipe.

Image

Then you have to grind off most of the washer down to the pipe. You might need to weld again after that.

Image

Now you have to grind off the back of the pipe so that the flange will slip into the reverse idler shaft slot.

Image

A 5/8 inch bolt fit perfectly inside the pipe.

Image

Now weld it in place.

Image

Now weld a grade 8 5/8 washer to the other end of the pipe and you have a new tool. 8)

Image

In action.

Image

Next up is to make a tool to drop in behind the counter shaft to allow the front bearing to be pushed out.
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
T. Highway
Moderator
Moderator
Posts: 1791
Joined: Thu Jul 09, 2009 4:57 am
Location: S.E. Wisconsin, USA, Earth

Re: SC M37

Post by T. Highway »

Very nice job.

Bert
1952 M37 W/W Rebuild @ 59% complete
Engine rebuild @ 95% complete
1985 M1009, 1990 M101A2, 2008 M116A3 Pioneer tool trailer
MVPA # 24265
NRA Life Member
NRA Cert. Personal Protection Pistol Instructor
NRA Cert. RSO
Class III RSO/KCR
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

Here is the start for the Cluster Gear Bearing tool.

The bottom of the MAP gas canister matches the size of the bearing.

Image

After cutting out the circle I painted a spare Cluster Gear end and outlined the shaft.

Image

Now the job was to cut out the middle.

Image

Image

Checking the fit.

Image

Ready weld the tab on.

Image

Finished tool

Image

In action.

Image

Image
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
T. Highway
Moderator
Moderator
Posts: 1791
Joined: Thu Jul 09, 2009 4:57 am
Location: S.E. Wisconsin, USA, Earth

Re: SC M37

Post by T. Highway »

That looks like it worked out well.

Bert
1952 M37 W/W Rebuild @ 59% complete
Engine rebuild @ 95% complete
1985 M1009, 1990 M101A2, 2008 M116A3 Pioneer tool trailer
MVPA # 24265
NRA Life Member
NRA Cert. Personal Protection Pistol Instructor
NRA Cert. RSO
Class III RSO/KCR
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

The last two weeks I spent putting it back together

All the Parts laid out.

Image

New Speedy Sleeve for the output flange:

Image

Starting to put it back together.

Image

Image

Image

Putting the lock ring on the input shaft the bearing kept popping out.
So I used a flat piece of metal to hold it in place.

Image

Nice!

Image

Image

Alan
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
T. Highway
Moderator
Moderator
Posts: 1791
Joined: Thu Jul 09, 2009 4:57 am
Location: S.E. Wisconsin, USA, Earth

Re: SC M37

Post by T. Highway »

Alan,

Did you reuse the old top cover or get a new one?

The reason that I ask is, if you reused the old cover was the pin tight for the shifter or did you have to repair it?

Bert
1952 M37 W/W Rebuild @ 59% complete
Engine rebuild @ 95% complete
1985 M1009, 1990 M101A2, 2008 M116A3 Pioneer tool trailer
MVPA # 24265
NRA Life Member
NRA Cert. Personal Protection Pistol Instructor
NRA Cert. RSO
Class III RSO/KCR
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

Since I was rebuilding Chris's transmission at the same time he was nice enough to scrounge two NOS shift towers. So they are nice and tight.

In fact when I was trying to get the angle of the shifter stub right when in neutral I went out to my truck that still has the original transmission in it and moved the shifter around.

Geeze that old shifter tower must be really shot. I could see the pin holding the ball wallowing all around and really loose. :shock:
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

Its been awhile since I posted anything about my truck. I have been taking things off of the engine and repairing as I go.

The starter on this truck was working but when I took it apart to replace the bendix the end plate that holds the brushes was horrible. I am on track to rebuild the starter.

While waiting on parts I decided to pull the head on the truck and see how bad things were as the truck has low compression. I didn't find any bad wear and other than the carbon at the top of the cylinder walls I can't feel any ridge. You guys take a look and see if you think I can get away with a ball hone job and new standard rings.

Image

Image

The Dark streaks on this image are from some oil that I sprayed to protect the walls.

Image
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
User avatar
sturmtyger380
SFC
SFC
Posts: 573
Joined: Sun Oct 21, 2007 5:13 pm
Location: Up State SC

Re: SC M37

Post by sturmtyger380 »

My 1953 M37 I am sure went though the rebuild program and was still in the Army up to the 1970's. The engine has a rebuild tag on it from 1973.

The housing looks green but I see black paint peaking out in spots.

I am trying to figure out what the label on the oil filter housing was as it does not look like the Fram ones I have seen. Any idea what the label on the side and top should say? Brand?

Image

Image

Top

Image

Image

Alan
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
Post Reply