Search found 30 matches
- Fri Jan 03, 2014 6:54 am
- Forum: Technical group
- Topic: m37 front springs winch truck/non winch truck
- Replies: 5
- Views: 874
Re: m37 front springs winch truck/non winch truck
If you add leafs (or is it leaves) to the front, you will encounter a U Bolt length problem. I just did this in anticipation of my V8 conversion. I added two leafs near the bottom of the stack and the passenger side U Bolt with the welded on saddle was not long enough. I had to get new U Bolts.
- Thu Jan 02, 2014 7:57 am
- Forum: Builders Blog
- Topic: 265 cdn m37
- Replies: 54
- Views: 20304
Re: 265 cdn m37
What is that steering box off of. Interesting
002
002
- Sun Dec 01, 2013 2:00 pm
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
Very Interesting.
- Sun Dec 01, 2013 4:16 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
OK Kaegi, I'll bite. As stated before I'm a newbie, what have been others experiences with stock radiator with a V8 conversion. Although I'm not yet sure the exact final configuration of my mill: I currently have a 360 block at the machine shop. It will either be .030 over stock bore with mild cam, ...
- Sat Nov 30, 2013 4:07 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
Sweet. Can't get any better then that. Thanks for your help. I will give them a call.
- Fri Nov 29, 2013 8:09 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
Bert, Well that should be all the measurements I need. Thank you for taking time. Brett, Was that Jegs Radiator specifically for a M or was it just a good fit produced for another make model. Although I know custom can be built to suit if you are willing to pay, I'd sure like to save the $ and get o...
- Fri Nov 29, 2013 5:11 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
That would be great. I need all dimensions. As stated before mine was NOT correct to the truck, infact they had cut a hole in the hood for the filler cap. I will probably be looking at an after market aluminum depending on my engine build. I was hoping to find a more mass produced stock reproduction...
- Wed Nov 20, 2013 10:12 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Re: Radiator Question
Thanks, Is that final measurement (1 1/4) from 1) the front to the flange? 2) the rear to the flange? 3) from outside of core to outside of core?
- Sun Nov 17, 2013 11:55 am
- Forum: General M37
- Topic: Front Fender Patch Panel
- Replies: 50
- Views: 7604
Re: Front Fender Patch Panel
Mid West Military replied (On a Sunday no less) to my e-mail. No Luck. The search continues. 002
- Sun Nov 17, 2013 5:16 am
- Forum: General M37
- Topic: Raleigh, NC to St Louie
- Replies: 0
- Views: 512
Raleigh, NC to St Louie
Transport needed for two M-37 doors from Raleigh, NC to St Louis Metro-East. Short and Simple.
- Sun Nov 17, 2013 5:14 am
- Forum: General M37
- Topic: Front Fender Patch Panel
- Replies: 50
- Views: 7604
Re: Front Fender Patch Panel
Thanks for your post Tom. Checked with Mseriesrebuild as well. No Luck. I'll be watching. VPW no, double checking with Mid West. I think I sent an e-mail couple of weeks back, and answer was no. But just to make sure I'll resend.
- Sat Nov 16, 2013 12:00 pm
- Forum: Swap Meet
- Topic: Fender patch panel
- Replies: 3
- Views: 682
Re: Fender patch panel
Out of stock. Replacement fenders good take offs $350 ea. from VPW
- Sat Nov 16, 2013 9:49 am
- Forum: Swap Meet
- Topic: BTP PTO 8000 pound winch with bumper
- Replies: 5
- Views: 1212
Re: BTP PTO 8000 pound winch with bumper
Where is it located? Thinking about shipping costs?
- Sat Nov 16, 2013 9:27 am
- Forum: Swap Meet
- Topic: Fender patch panel
- Replies: 3
- Views: 682
Fender patch panel
I am a newbie and just getting started. I purchased a 54 m-37 in fair shape to do a complete Rest/Mod 360 swap. I am looking for front fender repair panels, that have been reproduced in the past. The fender below the headlight and its support are well beyond repair on my project. It would seem the e...
- Sat Nov 16, 2013 9:24 am
- Forum: Technical group
- Topic: Radiator Question
- Replies: 23
- Views: 2256
Radiator Question
I am a newbie and just getting started. I purchased a 54 m-37 in fair shape to do a complete Rest/Mod 360 swap. I have collected some parts and found this board to be very helpful. So with that in mind I need a favor. My truck does not have the original radiator. It is similarly flange mounted but i...